20" iMac G4 Intel NUC Ivy Bridge AiO Mod (Videos)

A video demonstration of my updated iMac G4 mod/hack (NUC/Ivy Bridge Mountain Lion Hackintosh)

 

Part 1:

Introduction and General Overview (YouTube Link)

Part 2:

Turning It On and Testing It Out (YouTube Link)

So that pretty much completes this mod.  I have thought about new HD 21.5" LCDs to the top of the arm in a custom LCD case that mimics the iMac G4, but I am not sure that would add very much.  This monitor falls just short of HD and I have not had any issues with it in terms of quality.  Though its something to consider for the future.  I find that larger monitors start to look "awkward" with the base.  Although placing the Cinema Display on the top of the monitor worked.  It wasn't until I went back to the original that I realized it was "off".  It didn't droop or tilt, but it didn't move as smoothly as the original.  The neck was obviously designed very specifically for the native monitor.  This includes not only the weight, but the thickness and shape as weight distribution changes as you tilt and swivel the neck.  Unfortunately, without the R&D budget of apple, its hard to design a new neck, but the old one works beautifully with the native LCD.

I would still like to make this into a touchscreen and perhaps add an iSight.  The awkward size and Mac compatibility issue make this difficult.  While I have a capacitive screen that works, its thick and heavy and would require dramatic hardware changes (LED lighting with custom thin diffuser) or physical changes (altering the LCD case and front bezel).  I am still hopeful that touch films will eventually be readily available, adding touch capability of any size with negligible cha ges in thickness.

Anyway, I'll worry about that later and enjoy this computer for a while.  I have tons of pics from this and previous mods, as well as the ability to fill in gaps with surplus materials.  As such, I'm thinking about putting together a "Moving Picture" Video Guide.  Sort of a compromise between a written and video guide.  I'll be able to explain from start to finish, step by step, how to do this with audio and annotated pics.  Let me know if this sounds at all interesting or useful to anyway.  Thanks for reading/watching.

iMac G4 Ivy Bridge Hackintosh: Finishing Touches

Completed Mod

While the previous Sandy Bridge Mod worked fine, this board is simply a perfect fit.  It runs cooler, uses less power, keeps the optical drive, supports mountain lion, uses the native PSU (which not only ditches the external power brick, but it even provides 30 extra watts of power).  This is much more stable.  Only S3 sleep (S1 works fine) remains a problem.

A Great Fit

The two extra additions are the 12V to 19V upconverter, which powers the actual motherboard.

and the Wide Input PSU, which allows the peripherals (The optical drive and the Fan) to turn on only when the motherboard is on and activates the PSUs 24V line via its 5V switch.  Both these fit (although its tight) and work perfectly.

With the exception of some cosmetics, I have completed the back ports.  They include 4 USBs, though 1 is used by a small Bluetooth adapter, a 3.5mm audio jack, the native AC power plug, and a "fake" Firewire 400 plug.  Its fake because it isn't a true firewire cable, it is only connected to a 12V Molex/Ground, so it supplies only power.  This is for use with the Griffin ifire adapter which gets its power from firwire and its signal from a 3.5mm audio jack and has an apple minijack out for the apple pro speakers.  This is very much akin to the original apple pro speakers that came with the G4 Cube.  They used an external amp which plugged into a special "high voltage USB port".  So although the speakers are not directly plugged in like the original, with the iFire, no additional power source is needed.  I did not want to break open and try to internalize the iFire.  This would have wasted the valuable iFire and constrained this mod to only those speakers.  The iFire also allows lengthening of the speaker cable, which is far to short on the apple pro speakers.

Other small improvements include:
Using KeyMap4Macbook to allow the keyboard button to eject the SATA to USB drive.

Changing the Mac Mini Pic in Resources to the 20" iMac G4, so the iMac's pic displays in "About this Mac".

About this Mac

The Full View

I will do a video shortly and am hoping to combine old pictures and new pictures into a comprehensive guide for doing this, including parts list.

Almost all the shortcomings of my previous mod has been addressed.  I am really pleased with this and hope this is helpful to others interested in this mod.  Thanks for reading!

20" iMac G4 Mod Ivy Bridge NUC/AiO Hackintosh running OSX 10.8.2 Mountain Lion - Success

I still have to improve the cable management at the bottom of the dome. The ports on the back need to be completed an I have to make a final decision regarding audio options.

I am quite amazed at how well this mod worked. I will of course give a more detailed description shortly.

20" iMac G4 NUC/AiO Ivy Bridge Mod: SUCCESS!

20" iMac G4 / NUC Ivy Bridge Mod

Updates:

I'm happy to report that all problems have been solved and the motherboard fit test was successful.  This is currently the method I would recommend for those that want a 20" Ivy Bridge Hackintosh version of this mod.  As I noted in my previous post, while I initially believed I would not go in the direction of the NUC board, its remarkably small size and simplicity made it by far the best candidate for this mod.

Original vs NUC/DVD - Front

In multiple previous posts I have explained the advantages of having the core elements (processor/motherboard) of the mod at the top of the dome where ventilation is best.  In my previous ECX mod, the board only fit with the optical drive because I did not use the native PSU.  Because I wanted to use the native PSU, I did not believe fitting the optical drive was possible, but with this board it looks like it is going to fit. (Although nothing is definite until this is completed).  This board fits into the slot left vacant by the 3.5" HDD (the mSATA is on the mobo itself).  It pretty much fits into the grooves in the drive chassis requiring no alternation.  For comparison, I have taken side by side photos of the original optical drive and HDD in the drive chassis next to the shorter new dvd optical drive and the NUC occupying that area.  The height is pretty much the same and there is amble room for the connectors to fit as well.

Original vs NUC/DVD - Top

Problem Solving:

With this fitting at the top of the dome, I should have even a little but more room for components than I did with my previous mod.  This is because, there are less port extenders needed and no SSD is required at the bottom of the dome.  It will still be tight, but I have some wiggle room to address the problems that I brought up in my previous post.  Taking them one at a time:

1) USB Ports: A 4 port USB Hub leaves me with only 1 spare USB port, but solves the problem.  The addition of another hub or a larger one is likely.  A USB port supplies the 5V to the PSU.

2) The Fan: The directional fan is connected to the heatsink and I did not want to remove it.  I also wanted to keep the case fan.  Apple's connectors and colors are completely backwards from industry standards (Black is 12V, Red is Ground and the fan out is a 3pin Male connector, not Female).  The fan is also somewhat loud and old, so I decided to replace it.  I bought a Antec 92mm fan that had a molex out (there is no case fan output on the board).  There is a sense pin that I won't be using.  Because I won't have software fan control, I got a model with a 3 speed setting.  I put it on medium to reduce noise and may extend the controller to the back ports or simply leave it on this setting.

Wide Input Pico PSU

While 12V are readily obtainable from the PSU, the problem is that the PSU is always on.  So, the fan will spin as soon as the computer is plugged in, no matter if the computer is on or not.  As the computer does not have any 12V out, I will have to use some kind of switch.  Luckily, the PSU comes natively with a "switch".  The PSU relies on the motherboard to downconvert 12V to 5V then feed 5V back to the PSU to turn on the 24V line that powers the monitor's backlight.  Although there are many other ways to do this, I went with an elegant solution using what I had available.  Keep in mind this is not the only peripheral that needs power.  The optical drive requires 12V and 5V in either a molex or SATA power connector.  Luckily, I had a very small 20 pin PICO power supply with a WIDE INPUT range up to 24V. (Not all PICO PSUs can accept 24V, may sure before you connect).  I spliced the PWR input to the Green wire of the PSU (24V) which connects to the Inverter Wires as well.  I connected the ground to a native PSU ground.  As this is a standard 20 pin ATX based PSU, it won't work without a motherboard unless you ground the On Pin.  I have it connected to a switch, but will likely just leave in a wire, allowing the PSU to turn on as soon as it receives 24V DC input from the native PSU.  This produces the necessary 12V and even a 5V and has both a Molex and SATA power cable out.  I connected the Molex to the Fan (you only need the 12V line and ground), and the SATA to the optical drive.  Now we the peripherals will only turn on when the motherboard itself is turned on.

PICO PSU powering the optical drive

The Bypassed Power Switch

3) Power Switch: I did not want to damage the board, so I simply threaded small wires between the onboard switch and its solder points.  I did this to the front right and back left corners.  This was then wired to the case switch at the bottom of the dome.  These can be easily removed in the future if this board is ever repurposed.  In addition this does not effect the functionality of the original switch in any way.

The case switch I use is from my previous mod. Modeling clay was used to secure a momentary switch directly behind the peg that protrudes from the back of the plastic power button on the back of the iMac dome.

4) Audio: I am sticking with the Turtle Bay USB Audio solution from my last mod.  This allows for a standard 3.5mm audio jack out and also supports a 3.5mm Microphone in.  I have it wired to the microphone in the LCD housing.

5) Bluetooth: I have not found anyone who has had success with any half height mini PCI-E that supports Wifi and Bluetooth with Mac OSX.  So, I am simply going to keep my very small USB bluetooth solution.

6) Optical Drive: I am using a DVD Burner that gets power via the PICO PSU discussed in #2.  The connection to the mobo is via a SATA to USB 2.0 adapter cable.

12V to 19V DC-DC Upconverter

7) Power: While the option of splicing the AC to the to the existing AC plug with the NUC's powerbrick is not a bad one, it is somewhat of a waste of the 180 watt PSU that already exists in the machine.  Not to mention that I'm already including a second PSU (which is really being used only as a downconverter here).  The NUC requires 19V at (at least) 3.7A and the PSU is only supplying 12V (can't use the 24V because its only on with 5V from the motherboard).  Luckily, 19V is the typical notebook operating voltage and therefore upconverters are available.  Though there is a much smaller selection than for more common voltages (24V, 12V, 5V etc).  Many different shapes an sizes are available.  I got one in a familiar shape on ebay from a Chinese manufacturer for $20.  Its relatively small ( I may remove part of the heat sink surrounding it) and is a 12V DC to 19V DC upconverter at 4A.  This is exactly what is required and works flawlessly.

The Upconverter connected to PSU and NUC

The Upconverter gets 12V and Ground in from the Native PSU and sends 19V out.  I had a broken Laptop AC power adapter that had a DC input that perfectly matched the power in plug on the NUC.  The positive is the inside peg and the negative is the outer part.  Using a multimeter I ensured which wire was which and connected this to the power supply via the up converter.

The Fit Test:

The Secured NUC Motherboard

On a side note, I used a rubber sleeve to cover the drive cage where the NUC will go.  After some guess and check, I determined the place where the  NUC and USB connectors seemed to fit the best. To test fit, I used twist ties that went through the screw holes in the grooves intended for the HD and then through the motherboard screw holes.  These will be replaced with plastic locking ties to secure the motherboard in place.
One thing to make sure of is that the wifi antennae which goes through the metal faraday cage (Wifi signal will be severely reduced if the antenna is within the cage) is connected to the wifi card before the board is secured.

Build Pics:

A Mess of Wires, But A Working Mod

Video and Audio Test

Motherboard View

About This Mac Screen

Remaining Issues:

Obviously, there is a lot of cable management to do.  This will get much simpler once connections are directly soldered (connectors removed and alligator wires eliminated).  As I technically have more room at the bottom of the dome than the previous mod (also had a DC converter and a PICO PSU to deal with), I do not believe this will be difficult to fit.  The wire management, however, may be more involved.

There will a paucity of ports.  A 3.5mm audio out, a few USBs, and not much else.  If I had to do it over, I probably would not have bothered spending the extra money on the Thunderbolt equipped version.  There are so few available peripherals and there are so overpriced that I can not even test this. Perhaps this is somewhat future proofing, but I would imagine there will be further upgrades to this board before thunderbolt actually takes off (if it ever does).  That said, I would not have bothered with an ethernet extender anyway.  I've learned with this that the more you do, the more that can go wrong.  I am more than happy to keep it simple.  I also have the option of adding a powered USB hub with the 12V lines in the PSU.  Unlike my previous mod which was very close to its power maximum, this should have room to spare.

Concluding Thoughts:

Untili I have it assembled and have worked with it for a while, I'm cautious about speaking too soon, but I am very optimistic about this project.  Although to Core i5 Sandy Bridge to a Core i3 Ivy Bridge may seem like a lateral move, this board is simply a better fit.  Its lower power, quieter, and everything onboard works.  The incorporation of the native PSU while keeping the optical drive makes this virtually indistinguishable from the original 20" iMac G4.

Hopefully will finish soon! Thanks for reading.